Author Nordwand Published 5 min read

Measuring air temperature in the mountains: record the date before clearing the minimum

A person beside a ventilated thermometer shield takes notes while looking across a frosty landscape

A minimum temperature is hard to interpret later if you do not know the period it covers. Before resetting the display, write down the value, the date and time you read it, when the previous reset occurred and where you measured. Check your manual for the period the device records and how to clear it.

Check which period the minimum covers

Find the recording period and clearing procedure in the manual for your device. For example, the Shinwa 73045 manual says it displays the highest and lowest values since the reset button was pressed. Pressing it again clears the records and starts a new period. This example describes a particular thermometer with an external probe. Other devices may work differently, including after a battery change.

If you reset it at night and read it the next morning, record the minimum as the lowest value the device logged during that interval. If you do not know when it was last reset, mark the interval as unknown. Unless the device saves the date and time of the minimum, the time you read the display is not when the temperature reached that low. Labeling it as the minimum for the date you read it can misrepresent an interval that crosses midnight.

Once you have recorded the result, reset it for the next period and note the reset date and time. For devices with automatic updates, check how the manual defines the intervals. If you photograph the display before clearing it, check that you can read the digits and keep a separate note of the period.

What to record with the date

Keep the minimum, date and time of reading, date and time of the previous reset, place and device name together. Note the setup as far as you can, including inside or outside the tent, height above the ground, and exposure to direct sun, rain or wind. Mark unknown fields rather than guessing.

A location on a map or an approximate elevation helps identify the site. Some watches’ altitude readings are affected by pressure changes. Keep the displayed altitude distinct from the map elevation. Leave enough detail to find the measuring spot again.

If several people use the same device, agree on who resets it and when. If someone clears it before the reading is saved, the period may be lost. One option is to write the time of the reset in a shared note for whoever reads it next.

Readings taken under different conditions can be hard to compare

The Japan Meteorological Agency describes its standard as measuring about 1.5 m above grass, with the thermometer in a ventilated shield that protects it from direct sun. A pack thermometer or a device inside a tent has different placement, sunlight and airflow. Keep those differences in mind when comparing a personal record with official observations.

Note the measuring position because body heat, sun, the ground and nearby equipment can influence the reading. The Okinawa Meteorological Observatory explains that official thermometers are placed in shields that protect them from sun and precipitation while letting outside air pass through. Check the manual for portable devices too. Some instruments have different ranges for the sensor and the unit itself, so a temperature the sensor can measure may be outside the body’s operating range.

If you move the device, record when and where. If one interval includes multiple locations, such as inside and outside the tent, you may be unable to assign the minimum to a specific place. If the display shows an out-of-range value or an error, note the display and conditions and leave the temperature blank. Set up and operate the device within its specified limits.

Make a habit of checking before the reset

When breaking camp in the morning, it is easy to turn off the device or start a new period before checking the display. Use a set order, as you would for packing or checking the weather: read the number, write it down, reset, then record the time of the reset.

Keep paper dry and legible. If entering it on a device, check the date and time yourself and allow for the battery to run out. If you keep only a photo, add a note so you can identify the place and period later.

When comparing several days at home, check each observation period and setup. If the periods overlap or you moved the device partway through one, keep that context with the comparison. Numbers on their own cannot settle what happened.

In short: keep the minimum and its period together

Before clearing the minimum, record the displayed value, the time and date you read it, the previous reset time and date, and the place and setup. Check the manual for the device’s recording period and operation. If the period is unknown, mark it as unknown.

References and sources

Find your mountain community

Find hiking partners and join communities. Plan your next adventure with Nordwand.