When comparing two slopes with the same gain, pay attention to where they gain elevation. Using official map-reading materials checked on October 28, 2026, we'll compare three fictional profiles with the same gain and horizontal distance. Look for the differences between sections that one average would hide. The examples and note-taking method are suggestions from the editors.
Match the elevation intervals and the direction of measurement
On the Geospatial Information Authority of Japan's 1:25,000 topographic maps, intermediate contours connect points of equal elevation at 10 m intervals and thick index contours are spaced at 50 m. On 1:50,000 maps the intervals are 20 m and 100 m. Check your legend for line types and intervals first.
Neighboring lines on the same map do not always represent the same elevation difference. Supplementary lines can add 5 m or 2.5 m intervals, and 2.5 m lines carry their elevations. Read the elevations at both ends of each segment instead of treating every line as another 10 m. If the endpoints are between lines, the count won't give an exact remainder.
The National Mountaineering Training Center's guide for school clubs illustrates how closely spaced contours indicate a steep slope and wider spacing indicates a gentler one. A distance measured in millimeters on one map cannot be carried over to another scale, and an oblique measurement differs from the shortest gap between lines.
We'll compare profiles along a straight line on a map, each rising in one direction. The horizontal axis is horizontal distance along that line, and the vertical axis is elevation. Here gradient means the elevation increase divided by horizontal distance, averaged over a segment. The line need not follow the steepest direction, and the result does not describe the steepest part of the hillside or the actual trail.
Compare three 30 m climbs over the same 150 m horizontal distance
These are arithmetic examples, with no measurements from a real trail. Imagine three sections rising by 10 m each, from 100 m to 130 m. Assume a constant gradient within each section, without small rises and dips. The horizontal distances are 50, 50, and 50 m for A, 25, 50, and 75 m for B, and 75, 50, and 25 m for C.
Each profile gains 10 m three times, for 30 m over a total horizontal distance of 150 m. The overall average gradient is the same, 30 ÷ 150. All sections of A have a gradient of 10 ÷ 50. In B, the first section is 10 ÷ 25 and the last is 10 ÷ 75. The first has three times the average gradient of the last. The factor of three is a ratio of rise to horizontal distance, separate from the angle or how tiring the climb feels.
C reverses the order in B. It takes 75 m horizontally to gain the first 10 m and 25 m to gain the last 10 m. It matches B in total gain, horizontal distance, and overall average, and even in the values of the steepest and gentlest sections. The order differs, and combining the sections into one number hides that.
At 1:25,000, the distances on paper are 1 mm for 25 m, 2 mm for 50 m, and 3 mm for 75 m. A is 2 mm per section, B is 1, 2, and 3 mm, and C is 3, 2, and 1 mm. All are 6 mm long. These are scale conversions. On an actual map, print scaling and line thickness can limit how precisely you can measure.
Record totals, averages, and the order of the sections
For a planning comparison, make separate columns for start and finish elevations, total horizontal distance, each segment's rise and horizontal distance, and the order of the segments. In A, B, and C, the first two sets of values are the same. The order shows the difference between a uniform climb, a steep start, and a steep finish.
On a real map, record the direction of the straight line and where it crosses the contours. Use the scale to convert the map distance between crossings into horizontal distance and record the matching elevation interval. If sections have different elevation gains, compare rise ÷ horizontal distance for each rather than the spacing alone.
If you want to compare gradients along a trail, check the relationship between your straight line and the actual planned route. If the trail curves away from it, the line can pick up elevations on a different slope. Even measuring the route on a map gives its horizontal projection rather than the distance walked along the slope. Keep those distances separate in your notes.
Mark a segment unverified if it is hard to read, for example because lines overlap, a label can't be traced, or the supplementary interval is unclear. You can mark the closest lines as a clue. That alone neither establishes a precise maximum gradient nor shows that it is the only place to watch.
More lines and profiles still leave details between contours
GSI explains that supplementary lines are used where intermediate contours alone do not show gentle slopes or complex terrain adequately. An extra line gives another known elevation. The shape within each interval still needs interpretation, even where no supplementary line appears.
In fictional profiles A, B, and C, we assumed that each section climbs at a constant rate, so connecting the crossings directly gives the profile. On real ground, the crossings alone don't justify that assumption. The average cannot tell you the precise steps, trail surface, footing, or small rises and dips.
GSI Maps plots the elevation along a selected line or route and displays the value under the pointer on the profile or route. If the result differs from your table, check the location, route, line type, and scale. GSI Maps derives the elevations from elevation tiles. Accuracy depends on the underlying data and terrain, and small features may be missing.
Even knowing the gradient of each section doesn't determine walking time, how much effort it will take, or whether you can pass. Use the table to compare terrain before leaving. To check it on the trail, stop where your footing is stable and you won't block others. If there's no suitable spot, wait. A mark where the contours are close doesn't identify a good place to rest or make a decision.
Keep the order of the sections even when the averages match
Two climbs with the same total gain and horizontal distance can have different shapes if the gain is distributed differently. Use matching intervals and directions and record the order as well as totals and averages. A fictional profile is a calculation. Field measurements, maximum gradients, and safety need their own evidence. Distinguishing map readings, calculated averages, and unknown details captures differences that a single total would hide.
References and sources
- Geospatial Information Authority of Japan | Map symbols: intermediate contours
- Geospatial Information Authority of Japan | Map symbols: index contours
- Geospatial Information Authority of Japan | Map symbols: supplementary contours
- Japan Sport Council, National Mountaineering Training Center | First Steps for High School Mountaineering Clubs, map reading (PDF page 4, print pages 5–6)
- Geospatial Information Authority of Japan | Finding the elevation of the land
- Geospatial Information Authority of Japan | How elevation tiles are made and how GSI Maps calculates elevation