Author Nordwand Editorial Published Updated About 8 minutes

Fitting a hiking backpack: how to measure your torso length

Illustration of measuring torso length for a hiking backpack

When choosing a hiking pack, check how its size matches your torso as well as volume and weight. Torso length is measured along your back from the base of the neck to the level of the top of the pelvis. On a pack with a load-bearing hipbelt, this measurement is a starting point for fitting it at both the hips and shoulders.

Small, medium, and large cover different ranges by maker and model. Use your measurement to narrow down the options on the model's size chart. Then try it with a load and check where the belt and shoulder straps sit.

What torso length is and why it matters

A load-bearing hipbelt helps share weight between the hips and shoulders when it fits around the upper pelvis. The load distribution depends on the frame, belt shape, contents, and fit as well as torso length.

If the shoulder straps lift when the belt fits, or the belt shifts when you adjust the shoulders, the torso length or shape of the harness may not suit you.

How to measure your torso

Use the seventh cervical vertebra at the base of the neck as your upper landmark and measure down to the level of the highest points of the iliac crests. Another person can help check both landmarks while measuring.

What you need

Steps

  1. Find the base of your neck. Tilt your head slightly forward and find the bony bump near the base. Use the maker's diagram to locate the C7 starting point.
  1. Find the height of the iliac crests. Put your hands on your hipbones and find the highest point of the pelvic rim on each side. Mark the same height in the center of your back.
  1. Take the measurement. Bring your head back to a neutral position and stand naturally. Follow your back with the tape from the point at the base of your neck to the center of your back at iliac crest height.
  1. Repeat using the same landmarks. If the results differ substantially, find the neck and pelvis landmarks again. Repeat to check whether the readings agree.

The same measurement can correspond to small, medium, or large depending on the brand and model. Note your measurement and check it against the size chart for the pack you are considering.

Compare with the pack size chart

Many manufacturers list the torso lengths that each size fits. Check the product page, tag, or instructions for a range in centimeters and see whether your measurement falls within it.

If you fall between sizes, try both in a shop if possible. Even at the same torso length, shoulder width, body shape, and harness design affect the fit.

Models with an adjustable back system allow some fine-tuning. The range is limited, so start with a size intended for your measurement.

What to check when wearing the pack

Use your measurement to narrow down sizes, then try the pack on and check the points below. A shop may have weights you can use for fitting.

Hipbelt position

For packs designed to carry weight on the hips, adjust the padding around the upper rim of the pelvis. Follow the maker's position guidance and check that it doesn't slip or press hard on the abdomen or hipbone.

Shoulder harness attachment

Check whether the shoulder straps follow the curve of your shoulders. Attachment points vary by model and do not have to align with the top of your shoulder. If you find a large gap or rubbing at the neck, reassess torso length and harness shape.

Using load lifters

If there are load lifters above the shoulder straps, pull them enough to bring the load closer to your body. Suggested angles differ by model. Check that you don't lift the shoulder straps or create a pressure point by overtightening.

Gaps around the hips

Walk a little to check that the pads follow your hips and the belt doesn't slide when tightened. Follow the pack instructions for the space needed between the padding ends and the buckle.

Choosing a pack with a fixed torso length

For a fixed-length pack, compare sizes or models by trying them on. If your measurement falls between sizes, test with a load to see whether the hipbelt and shoulder straps both fit.

The hipbelt size can be wrong even if the torso length is right. For instance, a medium pack may fit your back but have a belt that can't tighten enough. Check the hipbelt sizing on the product page, too.

Next steps

Measure your torso with a tape and save the result on your phone or elsewhere. When buying, compare it with the model's size chart and try the pack with a load. You can ask people who use their packs in similar ways in Nordwand's Base Camp or communities for particular interests.

References

Find your mountain community

Find hiking partners and join communities. Plan your next adventure with Nordwand.